Search:

Type: Posts; User: printer2

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    8
    Views
    127

    It does not matter. You may get some glue squeeze...

    It does not matter. You may get some glue squeeze out to clean up on the tape side.
  2. Replies
    3
    Views
    190

    A plastic bristle brush, old tooth brush, soap...

    A plastic bristle brush, old tooth brush, soap and water. You want to see character afterwards?
  3. Replies
    1,903
    Views
    192,188

    Say what? https://i.imgur.com/KtbCumY.jpg

    Say what?

    https://i.imgur.com/KtbCumY.jpg
  4. It is always good to have some tricks in your bag...

    It is always good to have some tricks in your bag to pull out when you may need them.


    I will be making cheap and dirty instruments to give away to underprivileged school kids and am trying...
  5. I just did the same thing with a 22" six string...

    I just did the same thing with a 22" six string that I was making for myself. I hack an arm bevel on it after the body was done, I had issues with the neck joint and just filled with wood dust and...
  6. Replies
    5
    Views
    231

    I used a door for a bench in my other house. Flat...

    I used a door for a bench in my other house. Flat and I built RC airplanes onit.
  7. Went down to measure the one I am almost done, 17...

    Went down to measure the one I am almost done, 17 1/2" yes a nice size. No where near as pretty as yours, that bevel and sound port has me thinking of Mark II. I love your work normally but this one...
  8. Absolutely perfect. What size of instrument?

    Absolutely perfect. What size of instrument?
  9. Replies
    8
    Views
    517

    Who counts frets anyway, no one will notice.

    Who counts frets anyway, no one will notice.
  10. Sure. And if they are a little floppy just leave...

    Sure. And if they are a little floppy just leave them a little thicker.
  11. Make a form yo hold the sides to shape. Nothing...

    Make a form yo hold the sides to shape. Nothing fancy, could be just a couple of blocks at the waist screwed to a 2x4. Maybe one at the butt also.
  12. Replies
    11
    Views
    548

    I use a flush trim bit and a belt sander.

    I use a flush trim bit and a belt sander.
  13. Sure, a knife would be doable. Really hard to...

    Sure, a knife would be doable. Really hard to resaw though. Watch the Mexican luthier say, "You call that a knife?"
  14. I need to rebuild my bandsaw, no bearings and...

    I need to rebuild my bandsaw, no bearings and everything not essential is closed. Need to do work on my drum sander but I'll probably leave it till I build another one. Jointer needs work, table saw,...
  15. High levels of humidity to close a crack will do...

    High levels of humidity to close a crack will do little harm, if you see the crack closed it will be obvious when to stop.
  16. Replies
    28
    Views
    1,728

    Put a space in at the http :---------- and you...

    Put a space in at the http :---------- and you can past in a link.
  17. Thread: spotty wood

    by printer2
    Replies
    6
    Views
    352

    https...

    https ://www.acousticguitarforum.com/forums/showthread.php?t=431498

    Take out the space.
  18. Thread: binding glue?

    by printer2
    Replies
    10
    Views
    753

    Fish glue! Lots of time to fiddle. Mind you I...

    Fish glue! Lots of time to fiddle. Mind you I also used CA and Titebond. The biggest thing is a well fitting binding. Scrape the inside corner of the binding to give it a slight bevel or clean out...
  19. Thread: what a waste

    by printer2
    Replies
    17
    Views
    1,157

    Actually a chipboard out of exotic woods might be...

    Actually a chipboard out of exotic woods might be interesting.
  20. Thread: what a waste

    by printer2
    Replies
    17
    Views
    1,157

    We need a stiff razor edged tool to resaw with....

    We need a stiff razor edged tool to resaw with. One cut, perfect surface, no muss no fuss, no waste. And cheap.
  21. Thread: what a waste

    by printer2
    Replies
    17
    Views
    1,157

    I can't remember if I posted this here or not,...

    I can't remember if I posted this here or not, found the most flawless 2x4 stud after years of picking through Home Depot's pallets. Did a rough calculation, decided to go for it. Cut it into two...
  22. Replies
    5
    Views
    405

    The left one for the back, you spend more time...

    The left one for the back, you spend more time looking at the front, would be a shame not to have it shown to people when played.
  23. Replies
    8
    Views
    435

    I hate you. I need to make a machine.

    I hate you. I need to make a machine.
  24. Replies
    1,903
    Views
    192,188

    Those look real pretty.

    Those look real pretty.
  25. Replies
    13
    Views
    815

    The hanger bolts or the dowels? The dowels, Aria...

    The hanger bolts or the dowels? The dowels, Aria for one. The tenonless guitar, Stephen Kinnaird, the guitar is being finished and as bad as the picture is you can see there is no joint cut out of...
Results 1 to 25 of 480
Page 1 of 20 1 2 3 4